SOLOPLAN-FA_200012_Englisch.pdf
5 页数
1.7 MB
Download
<h1>SOLOPLAN-FA_200012_Englisch.pdf</h1> <p>Technical data sheet <br />SOLOPLAN®-FA <br />Special fibre reinforced floor levelling compound</p> <p>Material number</p> <p>Contents</p> <p>Unit of quantity</p> <p>Packaging</p> <p>Colour</p> <p>200012001</p> <p>25</p> <p>KG</p> <p>Bag</p> <p>Grey</p> <p>Areas of application <br />To level uneven substrates <br />On critical substrates such as wooden floorboards or mixed substrates <br />for manual and mechanical application <br />For rooms with a low moisture pressure <br />For heated and unheated substrates <br />For interior</p> <p>Product features <br />self-levelling floor levelling compound <br />CT-C30-F7 after DIN EN 13813 <br />Fibre reinforced <br />Layer thicknesses ca. 2 - 20 mm <br />Layer thicknesses of 2 mm - 40 mm with cement-based substrates <br />Rapid setting</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />1/5</p> <p>02/04/2025</p> <p>Technical data sheet <br />SOLOPLAN®-FA <br />Advantages <br />Fibre reinforced <br />Low stress <br />For use in restoration, renovation and modernisation</p> <p>Existing test certificates <br />AgBB certificate <br />EMICODE licence</p> <p>Technical Data <br />Material properties <br />Product components <br />Base material</p> <p>Consistency <br />Flexural strength (28 days, DIN EN 13813) <br />Abrasion test bonded with PVC in accordance with DIN EN 13892-7 <br />Compressive strength (28 days, DIN EN 13813) <br />Classification of the reaction to fire in accordance with DIN EN 13501-1</p> <p>1 component system <br />Special cement <br />Cementitious aggregates <br />Additive <br />Powdered <br />≥ 7 N/mm² <br />RWFC-550 after 16 h at 5 mm layer thickness <br />≥ 30 N/mm² <br />Efl</p> <p>Mixing <br />Mixing time <br />Water addition</p> <p>approx. 3 - 5 minutes <br />approx. 6 l - 6.3 l</p> <p>Application <br />Substrate temperature <br />Pot life <br />Consumption pro m² and mm layer thickness <br />Foot traffic after <br />Ready for covering with tiles <br />Application temperature <br />Hardening time / full resilience</p> <p>approx. 10 - 25 °C <br />approx. 45 minutes <br />approx. 1.6 kg <br />approx. 3 hours <br />approx. 8 hours <br />approx. 10 - 25 °C <br />approx. 28 hours</p> <p>Material rate <br />Material consumption rate according to the area of application</p> <p>Processing equipment <br />Aids/tools <br />Flat trowel <br />Surface rake <br />Stirrer <br />spiked roller <br />Clean mixing bucket</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />2/5</p> <p>02/04/2025</p> <p>Technical data sheet <br />SOLOPLAN®-FA <br />Suitable substrate <br />Cement-based screed (CT) <br />Calcium sulphate screeds (CA, CAF) <br />Concrete <br />Dry screeds <br />Raised floors <br />Floor levelling compounds <br />Tile bearing elements <br />Firmly adhering tiled finishes <br />Wood materials</p> <p>Preparing the substrate <br />Requirement for substrate <br />1. Dry <br />2. Load-bearing <br />3. Firm <br />4. Grippy <br />5. Free of cracks <br />6. Free of adhesion inhibiting substances</p> <p>Measures for substrate preparation <br />The substrate must correspond to the load-bearing capacities in accordance with DIN EN1991-1-1.</p> <p>Preparing the surface <br />1. Check the application substrate and determine the moisture content using the CM method. <br />2. Remove impurities, adhesion-reducing substances and binder accumulations/laitance layers. <br />3. Prime absorbent substrates with ASO-Unigrund-GE, ASO-Unigrund-K or ASO-Unigrund-PLUS. <br />4. Prime non-absorbent substrates / wood substrates with ASO-Unigrund-S or ASODUR-GBM (scatter with quartz sand 0.5 mm to 1.0 mm).</p> <p>Moisture content of the CM measurement</p> <p>Application <br />Mixing <br />1. Fill the water into a clean mixing bucket and mix with the powder component with a stirrer to produce a homogeneous, lump-free mass. <br />2. The mixing time is ca. 3 - 5 minutes.</p> <p>Application <br />1. Apply SOLOPLAN®-FA to the primed substrate, and use a suitable tool to distribute it evenly during the pot life. <br />2. De-aerate the fluid layer with a spiked roller (or another suitable tool) and induce it to flow; doing so improves the surface and the flow <br />decisively. <br />3. Setting SOLOPLAN®-FA must be protected against rapid water removal (e.g. due to a spraying several times with water or covering, high room <br />temperature, direct sunlight and draughts)! The temperature of the air, material and substrate may not fall below +5 °C during application, and <br />during the following week!</p> <p>Cleaning tools <br />Clean tools thoroughly with water after use.</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />3/5</p> <p>02/04/2025</p> <p>Technical data sheet <br />SOLOPLAN®-FA <br />Storage conditions <br />Storage <br />Store in a cool and dry place. Min. 12 months in the original canister. Promptly use opened container.</p> <p>Disposal <br />Product residues can be disposed of in accordance with disposal code AVV 17 01 01.</p> <p>Emission behaviour / building certification systems <br />Very low emissions in accordance with GEV-EMICODE, which normally results in positive evaluations within the scope of building <br />certification systems in accordance with DGNB, LEED, BREEAM, HQE. <br />Maximum quality level 4, line 8 in accordance with DGNB criteria "ENV 1.2 Risks to the local environment". <br />Suitable for indoor use in accordance with the French VOC Directive and Belgian Royal Decree C-2014/24239.</p> <p>Notes <br />A moisture measurement must be carried out using the CM method to assess whether it is ready to receive. <br />Sufficient ventilation below wooden floors, e.g. by including ventilation slots or installing special skirting boards with ventilation openings must <br />be guaranteed, particularly when laying vapour-tight coverings! <br />The sub-base for wooden floors must be consistently dry in order to avoid moisture damage due to rot and mould formation! <br />In order to reliably avoid pore formation, work ASO®-Unigrund into the substrate in a meticulous manner and allow thorough drying. <br />The installation location must be ventilated. However, draughts and direct solar radiation should be avoided during application and the <br />hardening process. The indoor temperature and floor temperature must be at least +5°C during application, and during the following week! <br />Air dehumidifiers may not be used during the first 3 days! <br />The condition of the substrate is essential to the success of floor levelling. Porous substrates negatively alter the flow behaviour of the <br />smoothing compound, therefore carefully prepare the substrate: clean and prime! <br />For calcium sulphate screeds, the carbide method moisture content may not exceed 0.5% if there is no floor heating system, or 0.3% if there <br />is a floor heating system at the time of levelling with SOLOPLAN®-FA. Prime the calcium sulphate screed with ASODUR®-GBM and scatter <br />quartz sand (Ø 0.5–1.0mm). Then remove the unbound quartz sand thoroughly and then level with SOLOPLAN®-FA to a layer thickness of <br />ca. 2 - 20 mm. The following moisture migration should be avoided. We recommend SOLOPLAN®-30-CA for levelling calcium sulphate <br />binded substrates, e.g. calcium sulphate screeds. <br />Direct contact between cement mortar and magnesite screeds leads to the destruction of the magnesite screeds through a chemical reaction <br />known as “magnesite pouring”. Moisture pressure from the rear of the substrate must be prevented through appropriate measures. <br />Mechanically roughen up the magnesite substrate and prime with ASODUR®-GBM epoxy resin. While the coat is still fresh, apply plenty of <br />quartz sand with a grain size of 0.5–1.0 mm. Perform the laying work after a further waiting time of approx. 12 - 16 hours. Remove the <br />unbound quartz sand meticulously. <br />It is imperative to rinse the mixing pump and the hoses in the event of work interruptions! <br />When using a PFT G4/G5 mixing pump, use the standard PFT G4 mixing screw, the D 6-3 rotor and the D 6-3 stator twister, and set the <br />water flow meter to approx. 370–420 l/h. The flow rate would then be ca. 20l/min. In case of larger layer thicknesses, we would <br />recommend using the pump unit, the R7-2.5 rotor and the R7-2.5 stator; in such a case, the water flow meter should be set to ca. 900 l/h. <br />The flow rate would then be ca. 40l/min. The PFT consistency test socket can be used to check and set the correct water addition level on <br />the basis of the slump. It should not exceed the level of 61 cm on a prepared substrate, and it should be monitored continuously during <br />application! <br />Border, field, building separation and movement joints should be carried over to or installed at the designated location; suitable means such <br />as RD-SK50 edging strips should be used to detach them! Crack control joints should be cut in after the SOLOPLAN®-FA has hardened to <br />the level of up to a third of the introduced layer thickness. <br />We recommend that SOLOPLAN®-30-CA be used up to a layer thickness of 10 mm for levelling mastic asphalt screeds of IC10 quality! <br />Only use clean tools and clean water! <br />Excessively rapid water removal (heated spaces or strongly-absorptive substrates) leads to a risk of crack formation! The fresh equalising <br />layer should be protected from excessively rapid drying and should be covered with tiles within 28 days. If this cannot be done in this period <br />of time, suitable measures such as the use of a protective film should be implemented to protect SOLOPLAN®-FA from excessively rapid <br />drying or deposits. <br />Calcium sulphate screeds must be protected with the ASO®-Unigrund-GE, ASO®-Unigrund-K or ASO®-Unigrund-PLUS primers prior to <br />laying.</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />4/5</p> <p>02/04/2025</p> <p>Technical data sheet <br />SOLOPLAN®-FA <br />Relevant regulations <br />Planning, inspection of substrates and building site circumstances, laying, grouting and subsequent <br />care of the work must be done in accordance with the relevant DIN standards and recognised rules of <br />technology (e.g. the ZDB Data sheets of the Zentralverband Deutsches Baugewerbe e.V.(German <br />construction Association) in the latest version. <br />Observe applicable safety data sheet! <br />GISCODE: ZP1 <br />Explanations <br />Conformity / Declaration / Verification</p> <p>The rights of the buyer with regard to the quality of our materials are based on our terms and conditions of sale and delivery. Our technical advice team will be happy to advise you <br />in the case of requirements that exceed the scope of the application described here. In order to be binding, a legally binding written confirmation is required. The product description <br />does not release the user from a duty of care. Lay a test area in the event of uncertainty. This version becomes invalid in the event of a new version being issued.</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />5/5</p> <p>02/04/2025</p>
